Late spring is the window for deck coatings: the timber has dried out after winter and the full heat of summer hasn't arrived. Oil applied to a hot deck in January flashes off before it soaks in.
In this post · 6 sections
Most people pick a deck finish by looking at a photo of someone else's deck. Then they find out what it takes to keep it looking that way. The finish you choose decides how often you'll be on your knees with a brush for the next ten summers, so it's worth choosing on purpose.
The three honest options
- Leave it bare: the timber goes silver-grey. Treated pine and many hardwoods are fine like this structurally. You'll still want a wash each year to stop it going slippery.
- Oil: soaks into the wood, brings out the colour, and wears away rather than peeling. It needs redoing regularly, often every year on a sunny, north-facing deck.
- Stain or film-forming coating: lasts longer between coats, but when it fails it peels and flakes, and getting it off for a recoat is hard work.
The trap is the third one. A film-forming finish on a deck that gets foot traffic and full sun will wear through first in the walkways. Patching it never quite matches, and stripping it back means sanding or chemical strippers. Many tradies who build decks steer people towards penetrating oils for exactly this reason.
The mistake that ruins oiled decks
Putting oil onto a dirty or grey surface. The oil seals in the grime and the grey layer, and the deck looks blotchy and dark. Wash it first with a deck cleaner, rinse, and let it dry properly, usually a couple of dry days. If the surface fibres are grey and furry, a light sand or a brightener first makes a big difference.
New treated pine is another trap. It's often wet from treatment and won't take oil well until it has weathered for a while. Ask whoever built the deck how long to wait.
Water blasting: careful
A water blaster at close range tears up the soft grain of pine and leaves a furry surface that drinks oil unevenly and goes grey faster. A deck cleaner and a stiff brush, or a water blaster on a wide fan held well back, does far less damage.
DIY or hire?
Oiling a deck is one of the most achievable DIY jobs around the house. Choose a dry, mild day, work in the shade where you can, and keep the coats thin. Hiring makes sense for large or high decks, decks that need stripping back from an old failed coating, or when you want boards replaced at the same time.
What it costs
Kettle's cost guide for carpenters puts rates at $50 to $90 an hour, with an ordinary job running from about $500 to $8,000, typically around $2,500. Cleaning and oiling a sound deck sits at the bottom of that range. Stripping an old coating, replacing boards and refinishing pushes it up.
What to send so it's quick to quote
- Photos of the deck, including close-ups of the worst areas.
- Rough size of the deck.
- What's on it now: bare, oiled, stained or painted.
- Which way it faces, and how much sun it gets.
- Any loose, split or soft boards.
The takeawayPick the finish you're willing to maintain, clean before you coat, and never put a peeling coating on a deck you'd rather oil.
Decks get fixed before the barbecue season. Customers who post on Kettle get quotes from local businesses, and the ones that reply first with a clear price tend to get the job.
- Pergola build on concrete padSilverdale, Auckland, Auckland · Posted this week
- Exterior house wash in SilverdaleSilverdale, Auckland, Auckland · Posted 3 weeks ago
Questions people ask
How often should a deck be oiled in New Zealand?
It depends on sun and foot traffic. A deck in full sun may need oiling every year, while a shaded one can go longer.
Is it OK to leave a deck unfinished?
Yes, many decks are left to weather to grey. Wash it regularly to remove grime and mould so it does not get slippery.
Can I water blast my deck before oiling?
Carefully. High pressure at close range damages soft timber. Use a deck cleaner and brush, or a wide fan held well back.